Introduction：
FSL is a spectrum analyzer device with a maximum frequency of 18 GHz produced by R&S of Germany, which is distributed by EUTTEST. The R&S FSL spectrum analyzer series includes six different products such as FSL3, FSL6, FSL18, etc. It's a lightweight and compact spectrum analyzer suitable for those who are concerned about the cost, but still need the high-end features of this analyzer for development, maintenance and production in a wide range of applications. The analyzer is suitable for a wide range of applications in development, maintenance and production.
R&S FSL Spectrum Analyzer Sequence Key Features:
- Frequency range from 9 kHz to 3 GHz, 6 GHz or 18 GHz
- Models with or without tracking source
- 28 MHz signal analysis bandwidth
- Low measurement uncertainty even in the microwave range
- Generic measurement applications such as waterfall charts
- Lightweight and compact design for on-site installation, maintenance and repair
- Optional battery operation
- Easy field upgrades with options
R&S FSL Spectrum Analyzer Sequence Technical Data:
The R&S FSL sequence consists of three different test frequency ranges: FSL3 (3GHz), FSL6 (6GHz), FSL18 (18GHz). If you have questions about product selection, contact EUTTEST for more information.
<<<<提醒：左右滑动表格>>>>| R&S FSL3 Model 0.03 | R&S FSL3 Model 0.13 | R&S FSL6 Model 0.06 | R&S FSL6 Model 0.16 | R&S FSL18 Model 0.018 | R&S FSL18 Model 0.028 | ||
| Frequency range | 9 kHz to 3 GHz | 9 kHz to 3 GHz | 9 kHz to 6 GHz | 9 kHz to 6 GHz | 9 kHz to 18 GHz (20 GHz over-range) | 9 kHz to 18 GHz (20 GHz over-range) | |
| Frequency accuracy | 1 × 10-6 | 1 × 10-6 | 1 × 10-6 | 1 × 10-6 | 1 × 10-6 | ||
| Use R&S ® FSL-B4, OCXO | 1 × 10-7 | 1 × 10-7 | 1 × 10-7 | 1 × 10-7 | Standards and R&S ® FSL18 | Standards and R&S ® FSL18 | |
| Resolution bandwidth | |||||||
| (an official) standard | 1/3 sequence 300 Hz to 10 MHz, plus zero span 20 MHz | ||||||
| Use R&S ® FSL-B7 | 1/3 sequence 10 Hz to 10 MHz, plus 1 Hz (FFT filter) eut test | ||||||
| Video bandwidth | 10 Hz to 10 MHz | 10 Hz to 10 MHz | 10 Hz to 10 MHz | 10 Hz to 10 MHz | 10 Hz to 10 MHz | 10 Hz to 10 MHz | |
| Signal Analysis Bandwidth | 28 MHz | 28 MHz | 28 MHz | 28 MHz | 28 MHz | 28 MHz | |
| phase noise | eut test typical 1 kHz from carrier, eut test , -103 dBc at 10 kHz (1 Hz) | ||||||
| Displayed Average Noise Level (DANL) | |||||||
| Using 300 Hz RBW | Typical -117 dBm | Typical -117 dBm | Typical -117 dBm | Typical -117 dBm | Typical -117 dBm | Typical -117 dBm | |
| With 1 Hz FFT RBW and preamplifier (FSL-B7. (FSL-B22 option) | 500 MHz: Typical -162 dBm 3 GHz: -158 dBm typical | ||||||
| Third Order Interception (TOI) | Typical +18 dBm | Typical +18 dBm | Typical +18 dBm | Typical +18 dBm | Typical +18 dBm | Typical +18 dBm | |
| oscillograph | Positive/Negative Peak, Auto Peak, RMS, Quasi-Peak, Average, Sample, eut test | ||||||
| Level measurement uncertainty | <0.5 dB (30 kHz ≤ f ≤ 3 GHz). <0.8 dB (3 GHz <f≤6 GHz). <1.2 dB (6 GHz <f≤18 GHz) | ||||||
| Tracking of generators | hasn't | be | hasn't | be | hasn't | be | |
| Frequency range | - | 1 MHz to 3 GHz | - | 1 MHz to 6 GHz | - | 10 MHz to 18 GHz | |
| output level | - | -20 dBm to 0 dBm | - | -20 dBm to 0 dBm | - | -30 dBm to -10 dBm | |
Wireless format analysis options supported by R&S FSL (additional purchase required):
- 3GPP HSPA
- WiMAX™
- CDMA2000®/1xEV-DO
- IEEE 802.11 a/b/g/n
- IEEE 802.15.1 Bluetooth®
- RFID
- MBMS
- DVB-C
Hardware Options:
- R&S®FSL-B4 Order No. 1300.6008.02, OCXO Reference Frequency
- R&S®FSL-B5 Order No. 1300.6108.02
- additional interface
- Video Out, IF Out, Noise Source Control, AUX Port, Connectors for R&S®NRP Power Probes
- R&S®FSL-B6 Order No. 1300.5901.02 R&S®FSL-B6 , TV trigger
- R&S®FSL-B7 Order No. 1300.5601.02, Narrow Resolution Filter 10 Hz to 300 Hz
- R&S®FSL-B10 Order No. 1300.6208.02, GPIB interface
- R&S®FSL-B8 Order No. 1300.5701.02
- Selective Scanning Function
- R&S®FSL-B22 Order No. 1300.5953.02
- RF Preamplifier, 3 GHz/6 GHz
- R&S®FSL-B30 Order No. 1300.6308.02, DC power supply, 12 V to 28 V
- R&S®FSL-B31 Order No. 1300.6408.02
- Ni-MH battery pack, requires R&S®FSL-B30
R&S FSL Spectrum Analyzer Sequence-Firmware Option:
- R&S®FSL-K7 Order No. 1301.9246.02
- AM/FM/φM measurement demodulator
- R&S®FSL-K8 Order No. 1301.9398.02
- Bluetooth® V2.0 and EDR compliant transmitter measurements
- R&S®FSL-K9 Order No. 1301.9530.02
- Power Probe Support
- (requires R&S®FSL-B5 or R&S®NRP-Z4 and R&S®NRP power probes)
- R&S®FSL-K14 Order No. 1302.0913.02
- Waterfall chart measurements
- R&S®FSL-K20 Order No. 1301.9675.02
- Analog and digital cable TV measurements
- R&S®FSL-K30 Order No. 1301.9817.02
- Noise Figure and Gain Measurement
- (requires R&S®FSL-B5 and a preamplifier)
- R&S®FSL-K72 Order No. 1302.0620.02
R&S FSL Spectrum Analyzer Sequence - 3GPP FDD BTS Application Firmware
- R&S®FSL-K82 Order No. 1308.7803.02
- CDMA2000® Transmitter Measurements
- R&S®FSL-K91 Order No. 1302.0094.02 R&S®FSL-K91 Firmware for WLAN applications
R&S FSL Spectrum Analyzer Sequence - WLAN Application Firmware
- WLAN IEEE 802.11 a/b/g/j Launch Application Firmware
- R&S®FSL-K91n Order No. 1308.7903.02 R&S®FSL-K91n WLAN Application Firmware
- WLAN Application Firmware
- R&S®FSL-K91 Upgrade to IEEE 802.11n
- R&S®FSL-K92 Order No. 1302.0236.02
- WiMAX™ IEEE 802.16 OFDM Application Firmware
- R&S®FSL-K92U Order No. 1302.0307.02
- Upgrading from R&S®FSL-K92 to R&S®FSL-K93
- R&S®FSL-K93 Order No. 1302.0736.02
- WiMAX™ IEEE 802.16 OFDM/OFDMA Application Firmware
- R&S®FSL-K84 Order No. 1302.0159.02
- 1xEV-DO Transmitter Measurements
